http://www.cnr.it/ontology/cnr/individuo/prodotto/ID282959

Measuring cutting effort and the surface quality obtained by routing across different wood grain angles: A comparison between Douglas pine and Aleppo pine|Mesure des efforts de défonçage et de la qualité finale en usinant en différents angles du fil: Comparaison entre le pin Douglas et le pin d'Alep (Articolo in rivista)

Type

Label

Measuring cutting effort and the surface quality obtained by routing across different wood grain angles: A comparison between Douglas pine and Aleppo pine|Mesure des efforts de défonçage et de la qualité finale en usinant en différents angles du fil: Comparaison entre le pin Douglas et le pin d'Alep (Articolo in rivista) (literal)

Anno

Alternative label

Aknouche H.; Goli G.; Marchal R.; Sandak J.; Zerizer A.; Butaud J.-C. (2012)
Measuring cutting effort and the surface quality obtained by routing across different wood grain angles: A comparison between Douglas pine and Aleppo pine|Mesure des efforts de défonçage et de la qualité finale en usinant en différents angles du fil: Comparaison entre le pin Douglas et le pin d'Alep
in Bois et Forets des Tropiques
(literal)

Http://www.cnr.it/ontology/cnr/pubblicazioni.owl#autori

Pagina inizio

Pagina fine

Http://www.cnr.it/ontology/cnr/pubblicazioni.owl#url

http://www.scopus.com/inward/record.url?eid=2-s2.0-84872545130&partnerID=q2rCbXpz (literal)

Http://www.cnr.it/ontology/cnr/pubblicazioni.owl#numeroVolume

Rivista

Http://www.cnr.it/ontology/cnr/pubblicazioni.owl#numeroFascicolo

Note

Http://www.cnr.it/ontology/cnr/pubblicazioni.owl#affiliazioni

Université m'Hamed Bougara de Boumerdès, UR-MPE, Avenue de l'Indépendance, 35000 Boumerdès, Algeria; Université de Florence, Deistaf, Piazzale delle Cascine, 50144 Florence, Italy; Centre Arts et Métiers, ParisTech de Cluny, Laboratoire Bourguignon des Matériaux et Procédés (LaBoMaP), Rue Porte de Paris, 71250 Cluny, France; Conseil National de la Recherche/IVALSA, San Michele all'Adige, Via Biasi, 75, 38010 - San Michele all'Adige (TN), Italy (literal)

Titolo

Measuring cutting effort and the surface quality obtained by routing across different wood grain angles: A comparison between Douglas pine and Aleppo pine|Mesure des efforts de défonçage et de la qualité finale en usinant en différents angles du fil: Comparaison entre le pin Douglas et le pin d'Alep (literal)

Abstract

The aim of this study was to compare a timber species commonly machined in Europe, in this case Douglas pine, with a little used timber species, in this case Aleppo pine from Algeria. A new method was developed to assess the cutting effort and the quality of the machined surfaces. The method was tested with Aleppo pine using a wood router held perpendicular to the surface and cutting continuously from 90°/0° to 90°/90° with or against the grain, so that the machining properties of the wood could also be assessed in comparison with other more commonly used timber species. The router bit, a rotary cutter with two carbide inserts, was used to bevel the edges of Aleppo pine discs cut from a board, which required the cutter to move continuously from an angle to the wood grain of 0° through to 360°. The cutting forces were measured using a 3-axis Kistler 9257A piezoelectric transducer fixed to the table of a digitally controlled router connected to a PC and a video capture board. The data were processed with Dasylab software. In parallel, the quality of the machined surfaces was tested with a tool where half of the cutting edge was new and the other half artificially blunted, using a new contact-free method developed by the CNR/ IVALSA research team. The results show that a little more cutting effort is required with Douglas pine than with Aleppo pine, and that the quality of the cut surfaces is far better with Aleppo pine than Douglas pine. (literal)

Prodotto di